Shop Autumn Sale >

Midas Finish Seal Lacquer Safety Data Sheet

The following safety data information is provided by the manufacturer of this product. Please read thoroughly and do not hesitate to contact us if you need further information. The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication.

This product contains Acrylic Co Polymer. May cause eye and skin irritation. Avoid contact with eyes, skin, and clothing. Use safety equipment when handling. Wash thoroughly after use. Keep out of reach of children. Please read Material Safety Data Sheet below.

EYE CONTACT: Flush eyes with water for 15 minutes, holding eyelids open.
SKIN CONTACT: Wash area thoroughly with soap and water. Seek medical attention if irritation persists.
INHALATION: Remove victim to fresh air until breathing is restored.
INGESTION: Induce vomiting. Seek medical attention.

1. Product/supplier information
Material/Trade Name: Midas Finish Seal Lacquer
Synonyms: Mixture
Based on Manufacturers MSDS: Unknown

2. Ingredients/exposure limit information

Chemical component % CAS No. TLV PEL REL
Acrylic Co Polymer 100 9003-01-4 N.E. N.E. N.E.

N.E. = None Established (Exposure Limits)

3. Physical properties
Vapour pressure (mm Hg):
Not available
Vapour density (Air = 1): Not available
Specific gravity: 1.040
Boiling point: 220°F (104°C)
Evaporation rate: Not available
Solubility in water: Complete
Appearance: Clear, viscous liquid
Volatility (%): Not available
Odour: Acrylic odour pH: 8.12
Melting point: Not available

4. Fire and explosion data
Flash point: Not available
Flammable limits: LEL: Unknown   UEL: Unknown
Auto ignition temperature: Not available
Extinguishing media: Water spray, ABC dry chemical and protein type air forms
Special fire fighting procedures: Fire fighters should wear full turnout gear and pressure-demand self-contained breathing apparatus (SCBA).
Unusual fire and explosion hazards: None known

5. Reactivity data
Stable: Yes
Conditions to avoid: None known
Incompatibility (materials to avoid): Strong oxidizing agents, acids
Hazardous decomposition products: Carbon monoxide, carbon dioxide
Hazardous polymerization may occur: No
Conditions to avoid: None known

6. Health hazard data
Primary routes of exposure: Inhalation, eye and skin contact
Acute signs and symptoms of overexposure: May cause irritation to eyes or skin
Chronic signs and symptoms of overexposure: None Known
Carcinogenicity: No   NTP   IARC   ACGIH   ISHA   PROP65
*No ingredients listed in this section*
Conditions that may increase overexposure potential: The extent of exposure to this product will depend largely on the intensity and duration of product use. Employers who supply this product for use by their employees must determine the conditions under which overexposure can result.
Medical conditions generally aggravated by exposure: None known

First aid procedures
Eye contact: Hold eyelids open and flush eyes for 15 minutes with large quantities of water. Seek medical attention if irritation persists.
Skin contact: Wash area with soap and water. Remove contaminated clothing. Seek medical attention if irritation persists.
Inhalation: Remove victim to fresh air. Restore breathing if necessary. Seek medical attention immediately regardless of apparent injury.
Ingestion: Seek medical attention immediately. Induce vomiting.

7. Precautions for safe handling and use
Actions to take for spills: Contain spill by absorbing with inert material. Neutralize with sodium bicarbonate before flushing to sewer
Waste disposal: Dispose of via a licensed firm in accordance with federal, state and local regulations (see EPA 40 CFR 261)
Precautions to be taken in handling and storage: Store solutions in insulated, closed containers in a cool, dry, well-ventilated area separate from incompatible chemicals.
Community right-to-know requirements: None known

8. Employee protection measures
Ventilation: Local ventilation is preferred to meet TLV requirements. General ventilation is acceptable, if exposure is maintained below TLV.
Respiratory protection: When airborne concentrations exceed the TLV or are unknown, use a NIOSH/MSHA approved respirator for dust/mist/vapours in accordance with OSHA respiratory protection requirements (29 CFR 1910.134).
Eye protection: Chemical safety goggles
Protective gloves: Rubber gloves are recommended
Other protective equipment: Rubber boots and apron
Work/hygiene practices: Eyewash station and safety shower should be available in areas of use. Wash thoroughly after handling product.

The information herein is given in good faith, but no warranty, express or implied, is made.

Shop Midas Finish Seal Lacquer

If you have any further questions, feel free to call our friendly team who will be more than happy to give you some advice through Facebook, Twitter, Email or simply calling us on 01872 573888 9am-4pm UTC.

Alternatively, for more information and how to's on all areas of jewellery making visit our other Gemstone Setting Advice pages.