How To Make A Ring Setting For A Free Form Cabochon

What gemstone will you use?

Creating a bezel setting for an irregular shaped stone can seem like a tough task - but don't worry, we've got a step by step tutorial to make it easy for you. You could use it on any irregular or free form gemstone you choose, such as a boulder opal or a piece of sea glass you found on the beach.

Within this jewellery making tutorial Hayley, Kernowcraft's Buyer shows you how to create a bezel set ring with a Larimar gemstone and beaded wire.

This is such a beautiful statement ring, with that gorgeous pop of colour and we hope it helps you find some inspiration for your next project!

-

The techniques within this jewellery making tutorial can be used to create a design with more detail or something that is simple to suit your taste and brand. Take a look below at Sea Surf Rocks amazing creations using free form stones - a boulder opal and sea glass! 

Step 1: Measure Bezel Strip

Begin by measuring the depth of your chosen stone and select the appropriate bezel strip length. The idea is to have just enough bezel to push over the stone during setting, so you can ensure the beauty of the stone is not hidden by too much bezel!

Tip: Where the stone begins to dome, is the height where you need the bezel. 

This is tricky on a free-form stone as they can be irregular but remember that the setting can be adjusted once the bezel is in place. 

Step 2: Cut Bezel

Next wrap the bezel strip around the stone and use a scribe to mark on the strip where you will need to cut. 

Always try and have the join on the straightest section of the stone for ease and use the edge of the bezel strip as a guide as this will give you matching ends; having ends that match perfectly will make it easier for you to solder them together. 

Tip: Use your files to create a neat flushed join if the ends are not perfectly aligned.

Step 3: Solder & Pickle

Before you solder the bezel strip check that your stone fits snuggly within the setting and that the ends actually meet.

Flux the join (solder paste already has flux incorporated in it so there is no need to flux if using this) and use medium solder paste or pallions to solder the ends together and then pickle your piece to remove fire stain. Remove from the pickle after a few minutes and inspect the join.

File and clean up the join using files and wet and dry papers.

Step 4: Attach

Now it's time to place the bezel on the silver sheet that you are using and use hard solder to join them together. 

The bezel must touch the sheet all the way around and there must be no gaps. Flux the area (if using pallions) where you are going to solder the bezel onto the silver sheet, place solder on the inside of the bezel then place onto your design.

Solder the 2 together and pickle.

Step 5: Trim Sheet

Using jewellery snips cut the excess metal sheet, leaving a 2mm gap around the edge so that you can add some beaded wire to the design.

Step 6: Wrap Beaded Wire

Next wrap the setting with the beaded wire (here we have used 1.5mm) and make sure that the wire touches at the ends. 

Using medium solder and the same soldering techniques mention in the previous steps, join the beaded wire to the setting on the 2mm section that surrounds the bezel setting.

Step 7: Create Ring Band

Next make a plain ring band using a ring size guide and the following calculation to get the correct size - calculation: diameter x pie + thickness of metal.

Once you have worked out the correct length that you need, mark it on the wire.

At this stage cut more wire than what you need so that the ends overlap next to each other, so that you cut through both ends at the marked length (this way you will have two ends that fit perfectly together). 

Using the solder techniques mention in the previous stages, solder the ring together and pickle.

Step 8: Solder Together & Pickle

Remove the ring from the pickle and shape it on a ring mandrel, remembering to turn the ring over on the mandrel for an even shape. 

File the edge of the ring where the setting will sit so that it is flat - this will make it easier to solder the two flat pieces together.

Place the bezel setting upside down on a soldering block and using a third-hand, place the ring with the flat edge down onto the setting and line it up centrally. Solder the two pieces together using easy solder. 

Pickle the piece.

Step 8: Polish

Clean up your design using files, wet & dry papers, silicon polishers/bench polisher and at this point check the depth of the bezel setting against your stone. 

Tip: Lay dental tape across the setting so that the stone can be easily removed after checking the depth, this will ensure you are happy with the depth. 

Once the stone is in the setting, it will be hard to get it out again. The aim is to have the minimum amount of bezel protruding above the stone, so that when you push the bezel edge over it you won't be hiding it. If the height of the bezel needs reducing - you can use your files to do this, you could also reduce the thickness of the bezel as this can make it easier to push or rub over.

Step 9: Push Bezel Over Stone

Using your pusher or bezel rocker gently push the bezel over the stone in a downward motion - be careful not to touch the stone especially if it is a soft or an opal as you may mark the top of it! 

Start at an awkward section and then move around the stone, each time pushing in the opposite direction to the section you have just done, until you have pushed the bezel over the stone all the way around. 

Step 10: Burnish

Continue to do this until you have a smooth finish that is flush against the stone. 

Use a burnisher on the section of the bezel you have just pushed or rubbed over, to give it a high polished look.

Create your bezel set ring with Kernowcraft...